The main appliances in your household should always be working at an optimal rate. Failure to keep them in an operable manner can result in some unnecessary circumstances, some of which can be nightmarish in nature. Take for instance, the toilet.
The last apparatus you’ll want to have is a toilet that has been clogged, and for obvious reasons. Thankfully, you won’t have to spend hundreds in order to clear the toilet of any existing obstruction. Prepare the surrounding area, in case of any unwarranted spill, and use one of the following ways to remove the clog.
1. Call the Plumber
Sometimes, a toilet clog will prove to be more difficult than initially expected. Should you find yourself having difficulty removing the clog, call your local plumber. Plumbing services like Drain Rescue Plumbers are reliable and you won’t necessarily have to spend a lot to get premium service. As always, you are better safe than sorry.
Unclogging a toilet can be as simple as mixing two ingredients together, to calling a servicer for assistance. Help is always around to fix the mess; you just have to decide which path you prefer to take!
2. Using A Plunger
The most obvious way to handle a clog in the toilet is by using a plunger. Slip some rubber gloves on and grab your plunger; the work might become a bit dirty depending on the clog inside. Put the plunger in the toilet and push down very gently at first.
This first push is done to essentially get rid of the surrounding air. Once a seal within the toilet has been established, begin pumping the plunger up and down a little bit more convincingly. Once the motions have been done several times, pull the plunger up sharply to break the seal. Water should rush down the drain, indicating that the clog has been removed.
3. Plumbing Snake
A plumbing snake is a useful tool to keep around, in the event that any sort of pipe in your appliance becomes clogged. The same sentiment applies to your toilet. If your toilet becomes clogged, a plumbing snake can easily remove the blockage due to its expertly-designed rubber coating.
To begin the process, insert the snake’s head into the toilet bowl. Turn the handle of the snake clockwise in a very delicate manner at first until you feel resistance. As soon as you feel the clog, wind the snake back up towards you. If you flush at this point, the loosened clog should be broken up enough so that the toilet flushes normally.
4. Baking Soda And Vinegar Mixture
This is one of the most commonly known, do-it-yourself liquids you can create to diagnose your inoperable appliances. If you do not have a plunger readily available, simply prepare a mixture of the two ingredients to use. Add one cup of baking soda to the toilet in question and wait a couple of minutes.
After the time has elapsed, pour approximately two cups of vinegar into the toilet. The subsequent mixture should sit in the toilet bowl for several minutes. Afterwards, flush the toilet; the concoction has worked if the clog has successfully been flushed down the toilet.
5. Dish Soap And Hot Water
Baking soda and vinegar is not the only liquid solution to put to use if your toilet has been clogged. Virtually everyone will have dish soap available in their household, so this is considered to be a viable replacement. First, squeeze about a quarter cup of dish soap into the toilet bowl and let it sit for five to ten minutes.
Afterwards, add some hot water into the toilet bowl. Just make sure the water isn’t at an extremely hot temperature. Once both ingredients have had time to sit within the bowl, the clog should become greased. This is because the dish soap acts as a lubricant, greasing the clog in order for it to be properly flushed down.
6. Wet/Dry Vacuum
It is critical to preface this with an important note; a regular vacuum should not be used. You run the risk of getting shocked if you do. Instead, rent a wet/dry vacuum from a local hardware store. To begin the unclogging process, place the hose into the toilet bowl and vacuum the water out.
Once this step is completed, wrap the hose in an old towel or rag to create suction. Turn the vacuum on, while steadily keeping the towel and hose in place. If done properly, the clog should be effectively sucked out. Don’t forget to sanitize the vacuum after the process!
7. Don’t Flush Multiple Times
This may seem like it is going against conventional thinking, but, rest assured, it is for your own benefit. If the toilet does not flush properly after one flush, leave it be for now. Any additional flushing will only cause more water to be pumped into the bowl. The flapper, which is located inside the tank, should be closed to prevent more water from entering inside the bowl.
